AGV Battery Selection: Sizing Voltage, Capacity and Charging Strategy
A warehouse that runs thirty automated guided vehicles cannot afford a battery guess. When an AGV dies mid-route, the whole material flow behind it stalls: pickers wait, conveyors back up, and supervisors start counting lost orders instead of shipped ones. Yet in most AGV projects we review, battery sizing was decided in a single afternoon - someone picked a voltage, guessed an amp-hour figure, and moved on. This guide breaks AGV battery selection into the three decisions that actually determine uptime: voltage, capacity, and charging strategy.
Under-sized batteries rarely fail dramatically. They show up as a fleet that hits 15% state of charge two hours before the shift ends, vehicles queueing at chargers instead of working, and pack temperatures climbing because the battery never gets a rest. All three symptoms trace back to the same root cause: the duty cycle was never measured.
Start with voltage, because it constrains everything else. The battery platform must match the AGV's drive motors, servo drives, lift motors and onboard DC-DC converters. Most warehouse AGVs and AMRs run on 24V or 48V platforms; heavier tugger and pallet-mover platforms often settle at 48V or above. Higher voltage delivers the same power at lower current, which means thinner cables, less heat in connectors, and better efficiency during acceleration - a real advantage for vehicles that stop and start thousands of times per shift.
Four checks settle the voltage decision:
1. Match the motor controller's rated input range first; the battery is a guest, not the host.
2. Check peak current for lift or hoist motors, not just drive current - lifting creates the highest instantaneous demand.
3. Confirm the BMS discharge rating covers peak plus simultaneous loads (drive plus lift plus onboard PC).
4. For 48V-class vehicles, verify charger availability and connector standards before locking the platform.
Capacity is where most projects go wrong, because spec sheets quote ideal numbers. The honest way is to work from measured energy per hour of operation. A practical formula: required Ah = (average working current in A x productive hours per shift) / usable depth of discharge. With LiFePO4 you can plan around 80-90% usable capacity without a meaningful cycle-life penalty, which is a genuine sizing advantage over chemistries that must be sized to shallow daily cycles.
Take a concrete example. A counterbalance-style AGV draws an average of 18A across a 10-hour shift, with lift motors pushing peaks to 60A for short bursts. Required capacity = 18A x 10h / 0.85 = roughly 212Ah. A 48V 210Ah LiFePO4 pack covers the shift with margin; a 100Ah pack would strand the vehicle with about four hours of work still on its schedule.
Before finalizing the amp-hour number, audit the variables that push average current up:
- Payload and lift frequency: every lift cycle with a full load adds significantly to average draw.
- Ramps and poor floors: climbing even a 3% grade can double drive current.
- Ambient temperature: cold warehouses reduce usable LiFePO4 capacity, and below 0 degrees C charging requires a heated pack or low-temperature charge protection.
- Route congestion: stop-start traffic raises average current versus what a free-flow simulation predicts.
The third decision - charging strategy - is where LiFePO4 changes the math entirely. Older fleets were planned around full shifts and overnight charging because their chemistry could not tolerate partial charging. LiFePO4 has no memory effect and handles shallow cycles extremely well, which unlocks opportunity charging: vehicles top up in 5-15 minute windows at docks, transfer points, or end-of-line positions.
Three charging strategies dominate AGV fleet design:
- Overnight full charging: simplest infrastructure, but requires the largest battery because one pack must survive the entire shift.
- Opportunity charging: smaller packs plus more chargers scattered across the floor; ideal for dense 24/5 or 24/7 operations.
- Battery swap: lowest vehicle downtime, but demands spare packs, a supervised charging room and strict connector standardization.
For a 24/6 distribution center we typically recommend 48V LiFePO4 packs sized to about 70% of the full-shift requirement, paired with two or three opportunity-charging points per route loop. The pack then spends its life in the 30-80% state-of-charge band where LiFePO4 cycle life is at its longest - fleets on this pattern commonly see well beyond 3,000 full-equivalent cycles before capacity fades to 80%.
Beyond sizing, three LiFePO4-specific features matter for AGV fleets. First, a quality BMS with CAN bus or RS485 communication lets the fleet management system read real-time state of charge, so dispatch software can schedule charging instead of guessing. Second, cell-level balancing keeps the pack healthy through the thousands of partial cycles that opportunity charging creates. Third, thermal design: warehouse ambient ranges of 0-45 degrees C are usually fine, but cold-room and freezer applications need heated cells or charge-inhibit logic below freezing.
Five sizing mistakes appear again and again in failed AGV projects:
1. Sizing from the motor's nameplate peak current instead of measured average current, producing oversized packs and wasted budget.
2. Ignoring charger placement, then discovering vehicles travel 200 meters to reach a charging point.
3. Forgetting the onboard computer, sensors and wireless links, which add a continuous 3-5A baseline load on their own.
4. Designing for the best day instead of the worst day - peak-season duty cycles should set the number.
5. Leaving no headroom for fleet expansion or gradual capacity fade; plan 15-20% margin from day one.
Before signing an AGV battery purchase order, put these points in writing: measured duty-cycle data from a pilot vehicle; the BMS communication protocol and a documented register map; a cycle-life warranty tied to your actual duty profile; charger profile compatibility with your charger vendor; and a clear definition of end of life, usually 80% of rated capacity.
For pack options across voltage platforms, browse our Motive Power Battery category page, which consolidates the 24V through 48V-plus formats most AGV builders specify. The 48V Lithium battery product page covers the high-capacity sizes used in heavier tuggers and pallet movers, and our E-Mobility & Logistics solution page shows how these packs integrate into complete vehicle programs.
AGV battery selection is not a parts-picking exercise; it is an energy budget. Measure the duty cycle, size voltage to the drivetrain, size capacity to the worst realistic shift, and choose the charging strategy before choosing the pack. Fleets that follow that order get batteries that age gracefully and vehicles that finish every shift - and the fleet manager stops thinking about batteries altogether, which is exactly the point.
Get a Quote